本帖最后由 beatles 于 2019-2-20 14:23 编辑
上政府网站看看要求吧！
https://www.building.govt.nz/building-code-compliance/h-energy-efficiency/h1-energy-efficiency/building-code-requirements-for-house-insulation/house-insulation-requirements/
House insulation requirements
[size=0.9375em]You need to meet the energy efficiency requirements set out in the Building Code, whether you are building a new home or making additions or alterations to an existing home. [size=0.9375em]The requirements vary for different parts of the country, to ensure New Zealand homes are fit for purpose. More insulation is needed for houses in colder climates. [size=0.9375em]There are three main ways to check you comply with the Building Code requirements. They are the: - Schedule Method
- Calculation Method
- Verficiation Method.
[size=0.9375em]The table below summarises the construction R-values specified in the acceptable solution for a house with timber-framed walls (low thermal mass). Table 1[td]
| Climate Zones 1 and 2
| Climate Zones 3 | | Roof | R 2.9 | R 3.3 | | Walls | R 1.9 | R 2.0 | | Floor | R 1.3 | R 1.3 | | Heated floors | R 1.9 | R 1.9 | | Windows | R 0.26 | R 0.26 |
[size=3.125em]+[size=0.875em]View full table
[size=0.9375em] [size=0.9375em]Construction R-values are for the complete building element (such as the roof or wall), not just the insulation product. [size=0.9375em]Construction R-values of the complete building elements are different to the insulation (product) R-values. The extent of difference depends on the construction details. [size=0.9375em]Construction R-values for building elements can be determined using: Additional requirements- The total window area must be ≤ 30% of the total exterior wall area.
- The combined window area of the east, south and west walls must be ≤ 30% of the combined area of these walls.
- The total skylight area must be ≤ 1.2m².
- The total area of leadlight glass must be ≤ 2.6 m².
- Downlights must be classed CA80, CA135, IC or IC-F to compy with the Electricity Safety Regulations.
- The R-value of carpets or floor coverings must not be included in calculation of floor R-value for heated floors.
- For heated walls or ceilings, higher R-values are required (walls R 2.6, ceilings R 3.5).
R-values for common construction types
On this page:
[size=0.9375em]The BRANZ House Insulation Guide provides construction R-values for common construction types. You can find some of the examples here: Roofs[size=0.9375em]In an uninsulated house more heat is lost through the ceiling and roof than any other part of the house, making the roof the top priority for insulation. Pitched timber-framed roof - R 3.3[size=0.9375em] Skillion roof - R 3.3[size=0.9375em] Walls[size=0.9375em]About 22 percent of heat from an average uninsulated home is lost through the walls. It can be difficult to insulate the walls of existing homes, but it’s well worth insulating walls in new houses. Timber-framed wall with brick veneer cladding - R 2.0[size=0.9375em] Timber-framed wall and weatherboard cladding - R 2.0[size=0.9375em] Floors[size=0.9375em]Around 14 percent of heat is typically lost through the floor. Installing underfloor foil insulation can be risky. [size=0.9375em]Risks when installing home insulation has information about underfloor insulation. Concrete stab on ground - R 1.3[size=0.9375em] Suspended timber froor - R 1.3[size=0.9375em] Windows and skylights[size=0.9375em]Windows are the weakest link when trying to retain heat inside during winter or keep it out during summer. [size=0.9375em]Windows are cold during winter because they lose so much heat, which can produce a downdraft of cold air and condensation. Windows also have a large influence on overheating during summer. The use of tinted or low glass, eave overhangs or other shading can limit summer heat and fading. [size=0.9375em]Double glazing is a big improvement over single glazing, although doubleglazed windows still conduct much more heat than walls, floors or roofs. [size=0.9375em]Window frames have a big effect on heat loss and should be carefully selected if maximum insulation is desired. [size=0.9375em]Aluminium window frames conduct heat from inside to outside very easily. Inserting thermal breaks into aluminium frames reduces the heat flow considerably. [size=0.9375em]Further improvements to window performance can be made by using wood or PVC window frames, by the type of glass used and by the gas pumped between the panes of glass. Double glazed aluminium - R 0.26[size=0.9375em] Single glazed wood or PVC frame and low emissivity class - R 0.27[size=0.9375em] High performance double glazed - R 0.48[size=0.9375em] [size=0.9375em]There are numerous window types available. You can find the R-values for them in: - NZS 4218
- BRANZ House Insulation Guide
- on Design Navigator
[size=0.9375em]You should refer to he manufacturers’ recommendations for all windows to ensure there is adequate support to carry the weight of the windows.
| 
发表于 2019-2-18 13:12:24
分享
收藏
变色卡
发表于 2019-2-20 14:24:04
