- UID
- 87574
- 热情
- 6296
- 人气
- 9186
- 主题
- 178
- 帖子
- 5006
- 精华
- 20
- 积分
- 10442
- 分享
- 0
- 记录
- 0
- 相册
- 2
- 好友
- 27
- 日志
- 0
- 在线时间
- 6859 小时
- 注册时间
- 2006-9-10
- 阅读权限
- 30
- 最后登录
- 2025-2-25
   
升级   8.84% - UID
- 87574
- 热情
- 6296
- 人气
- 9186
- 主题
- 178
- 帖子
- 5006
- 精华
- 20
- 积分
- 10442
- 阅读权限
- 30
- 注册时间
- 2006-9-10
|
本帖最后由 nzcy 于 2012-4-14 23:21 编辑
我是给楼主安装天线的Kevin.
楼主英文好可以看看这个三角台的接收方法。
这是个模拟信号频道。新老电视都应该可以接收。但商店里卖得freeview解码器是收不到这个台的。
如果想继续看这个台可以使用您家的室内天线或者刚刚安好的鱼骨天线直接连到电视机后的插座,用电视机的模拟信号模式就可以看了。如果哪点不明白还可以打电话问我。
Tune In
Triangle Television's signal is transmitted from Waiatarua in West Auckland, Pine Hill on the North Shore and from Remuera. It reaches north beyond Whangaparaoa, east to Maraetai and south to the Bombay Hills. Most homes in the Auckland region is able to receive a clear picture and sound.
However, reception will be affected in areas situated in valleys or shadowed by physical features such as hills and tall buildings.
It is highly recommended to install a UHF aerial to attain a clear picture.
If you already have Freeview HD (i.e. terrestrial reception, not satellite) and you have recently replaced your CRT TV with flat screen model, you most probably are ready to watch Triangle TV. On your remote, there should be a button saying [analogue/digital], which toggles between the two broadcast systems.
If your TV set is not tuned into Triangle TV, consult the operating manual for your TV set for tuning instructions specific to your model. This will tell you how to find and store new channels.
Triangle TV's frequencies:
Waiatarua UHF 41 or 631.25 MHz
Remuera UHF 52 or 719.25 MHz
Pine Hill UHF 42 or 639.25 MHz
IF YOU NO LONGER HAVE THE MANUAL, TRY THESE INSTRUCTIONS:
Find the tuning controls which are usually located either behind a door or removable panel on the front or the side of the set.
Choose a channel on your TV set not used for another station (e.g. 5 or 6) and move to that channel.
It's usually best to tune your TV set manually. If you have automatic fine tuning (AFT) make sure this is turned off.
If your TV has a [preset] button, press this.
The screen may display [VHF], either switch the band selector to [U] for UHF or press the [Band] button again until UHF appears.
Adjust the tuning up/down until a clear picture and sound appear. Press the [Preset] or [Memory] button to save the channel settings.
Turn the AFT control back on. As every model of TV and video recorder seems to have different tuning controls, it is difficult to give specific tuning instructions that will match every TV and VCR.
It is suggested you call the manufacturer if you are having problems. If you find you need further help call your local aerial installe |
|